How To Repair Soap Dish In Bathtub

These days the costs to refurbish or remodel a bathroom are dizzying.  Old bathtubs become hard to clean and show stains soon later cleaning due to the worn out porcelain surface.  In lieu of removing a tub, dissentious the tile and replacing it with a cheap new steel tub, many homeowners are choosing DIY bathtub refinishing to refinish their bathtub themselves.

Some erstwhile porcelain tubs are extra deep and fifty-fifty if replacement were an selection, many folks would like to keep that deep old tub.  Do-it-yourself types have the option of using hardware store bathtub refinishing kits or for an even meliorate product,  purchasing bathtub refinishing kits online.

Whilst the production quality and awarding methods differ, the bones steps for properly refinishing a bathtub are the same.

DIY Bathtub Refinishing Tools and Supplies

You lot really do not need many tools to refinish a bathtub.  Some tools, such as an orbital sander, tin exist skipped by manually hand sanding.  Hither is a breakup of what is needed to reglaze a tub.

• Putty Pocketknife
• Razor Scraper
• Spiral Drivers
• Utility Knife
• Orbital Sander
• Respirator
• 120 grit sandpaper
• Scouring powder
• Green Scotchbrite Pad
• Ventilation fan
• Bondo or polyester filler for repairs
• Lacquer thinner
• Tough chemically resistant gloves
• Centre protection
• Silicone Digester
• Mildew resistant bathroom caulk
• Masking record
• Masking paper
• Paper towels
• Painters tack textile
• Drop cloth
• Plastic to protect surfaces if spraying

Prepping the Bathtub for Refinishing

Plough on the ventilation fan in the bathroom if it has ane.  Open the bathroom window if it has ane and identify a fan blowing towards the outside (mask around the fan to seal information technology off from the window so air does non depict effectually the fan).

If the fan will not fit in the window then place a fan bravado in at the bathroom door and use plastic to seal off the door around the fan to forcefulness air out of the smaller bathroom window.

If you have no bath window, identify a fan blowing out of the bathroom door into the dwelling house.  Bathtub refinishing fumes are dangerous and you practise non want yourself or anyone in the domicile animate them.

Always wear hand and eye protection.
Remove the overflow plate from the tub and brainstorm the caulk removal stage.First by removing the caulk around the tub where it meets the tile surround.  Take your utility pocketknife with a sharp blade and start cutting at the caulk.

Cut from above on the tile side and from the side on the bathtub side (vertical and horizontal cuts).

Make a few passes and the old caulk will start loosening up.  Accept your putty knife and start working the caulk off as yous did with your utility knife, from the tile side, and from the bathtub side.

Do not worry well-nigh blackness tool marks on the tile or tub; these volition clean off with lacquer thinner later.  Now that the majority of the caulk is off, have your razor scraper and start removing whatever residue caulk off the tile and tub.

Later, clean upwardly your mess.

Silicone volition ruin your refinish job.
If silicone caulk was used to caulk your bathtub, all of information technology has to go.  Silicone residue is hard to remove and no refinishing product can adhere to the tub if whatsoever silicone is present.  After removing all the caulk use a silicone digester and follow its instructions for use.

3M Silicone Remover

Start cleaning the tub.
Take your razor scraper and start scraping the tub under the soap dish expanse and the corners of the tub.  Wait for lather scum to showtime flaking off from your razor.  Scrape the entire tub looking for soap flakes and piece of work off equally much every bit you can with your razor scraper.

Scrape around the drain closely to remove any plumbers putty or droppings.

Utilise Barkeepers Friend equally a scouring powder and scrub the unabridged tub with a light-green Scotchbrite pad.  Using a sponge, rinse the tub thoroughly and repeat the scrubbing process again.

Cleaning the tub of all oils and lather scum is the nigh critical aspect of bathtub refinishing.  Pay special attention around the drain.  This is the highest failure surface area.

After rinsing the tub, audit for any caulk, silicone or soap film that was missed and remove these contaminants.  Afterwards, dry the tub well with your paper towels.

Make your bathtub repairs.
At present is the time to make whatsoever repairs to the tub.  Lay down a few sheets of masking paper in the lesser of the tub and mix upwards some polyester filler such as Bondo or even amend Evercoat or Dolphin Coat.

Utilise a putty knife or bodywork spatula and apply your glaze over the chips or other defects in the tub.

Let this dry a few minutes and then gently sand off the backlog.  Echo if necessary.  If you are carving the tub in acrid, etch before repairs.  Information technology is non a bad idea to apply some bonding agent to the repair areas before making the repair.

Go prepare to mask.
Dry the tub well with paper towels making certain there is no h2o under the outside edges of the bleed.  Using your orbital sander or by hand sanding, begin sanding with 120 grit newspaper or sanding disks (put your respirator on starting time).  Sand whatever rust areas and sand the muddy overflow area.

Sand the corners of the tub and where the tub meets the tile.  Sand the entire tub downwards well.  Take a newspaper towel and wipe all of your grit towards a back corner of the tub away from the bleed.

You tin record downwardly a piece of masking paper to use every bit a "dustpan" and brush your dust onto information technology, wad it up and discard.

Put on your prophylactic gear: gloves, respirator, and eye protection.  Begin soaking a newspaper towel with lacquer thinner and start wiping downward the tub and firsthand tile  (make sure there are no sources of ignition in the room like open up flames or smoking).

Mask the tub.
After waiting for any lacquer thinner to dry, brainstorm masking off the tile with 3/four″ or i″ masking record.  Mask all the way around the tub and flooring in front of the tub.  Mask the drain by applying tape strips over it and so cutting around the drain with a sharp razor blade and removing the excess tape.

Have your masking newspaper and re-mask over your tape with more than tape and paper this time.  Place a latex glove over the faucet and the shower head.  They will make up one's mind to baste in the middle of your refinishing job.

Later masking your tub, information technology is time to use the bonding agent that came with your bathtub refinishing kit.

Utilize your DIY bathtub refinishing product.
Accept your tack cloth and make certain you have cleaned out all the dust in the tub.  Put on your respirator, gloves, and eye protection.

Before refinishing your tub, mix your product together referring to the included instructions.  If you are not using a spray gun and then cutting in your corners, along the tile, and effectually the drain with your included brush.

Use a fine foam roller to apply the product to the rest of the tub.

Bathtub reglazing kits may have varying directions and then read the awarding instructions that came with your kit.  If in between coats you notice that you take a run, wait for information technology to dry a bit and then wet a latex-gloved finger with lacquer thinner and gently rub it out, keeping your finger wet.

The Top Rated  DIY Bathtub Refinishing Kit

AquaFinish Bathtub and Tile Refinishing Kit

After a few minutes of completing your product awarding, remove the masking on the drain.  Wait a few hours (not days) to remove the remaining masking.  You risk grout trash and dust falling into the tub when removing the masking.

Make sure the tub is dry enough and then if whatsoever dust falls into the tub it is not going to stick.

If any grit does autumn in, don't touch it until the next day when the tub is fully dried.  Wait a expert 2 days to supercede your overflow cover.  If the overflow cover is ugly, you can option one up at the hardware store for a small cost.

 After waiting a 24-hour interval, you tin then re-caulk your newly refinished bathtub.  Choose a non-silicone caulk with anti-mildew properties such as this one from DAP.  The color "beige" is a better match than pure white.

You can also choose Loctite Polyseamseal but brand sure the tub is fully dry.  It is easier to control the caulk using the squeeze tube.  Cut off simply a small-scale bit of the tip at the recommended angle.

Employ the caulk and then put on a latex glove and shine the caulk with your finger. Hold your manus every bit flat to the tub as you can while smoothing the caulk.

Bathtub reglazing is not difficult.  Just make certain the tub is as make clean as possible before any production goes on!

More than Bathtub Refinishing Articles tin can exist found here:
 Bathtub Refinishing Information

Getting started professionally refinishing bathtubs?
Hither are a few tips for success.

• Get the highest phase HVLP blower y'all can afford.
• Read more nearly HVLP spray guns here.
• Set up your HVLP gun fan at 6″ to 8″ and shoot from about the aforementioned distance.
• Turn your air pressure to the lowest yous can, but proceed a skilful atomizing force per unit area.
• Never over-reduce your products.  It never helps and only makes for runs and crude tubs.
• Exercise non reduce with cheap lacquer thinner.  It is usually contaminated with water. Lacquer thinner as a reducer makes tubs lose their gloss in a few months.  It is for cleaning your gun only.
• Do not skip cleaning the tub and and so cleaning the tub once more.
• One coat of topcoat is never plenty.
• Always apply a measuring mixing loving cup.
• Always use a check valve on your gun.
• Y'all cannot clean a tub with lacquer thinner.
• E'er mix and strain your cloth earlier information technology goes into your gun loving cup.
• Silicone and soap film is the enemy.
• No matter what y'all think your over-spray will be, always plastic off the mirror, vanity, and toilet.
• Fifty-fifty though it is a hurting to set-up, always become out your extraction fan.  It helps with trash in the tub and dry spray on surfaces.  It keeps you lot from running out of the bathroom later a coat, quickens flash fourth dimension and keeps your customers away from fumes.

Source: https://edmondbathtubrefinishing.com/how-to-refinish-a-bathtub-diy-bathtub-refinishing/

Posted by: williamstweveseen1994.blogspot.com

Share this post